How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
We've stumbled upon this article about Installing A Bathtub down the page on the web and figured it made sense to relate it with you over here.
Setting up a bathtub isn't exactly brain surgery, however it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a new one is also a moderately tough task. If the old bathtub is readily obtainable, the task can move immediately; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need a helper to move out the old tub as well as embeded in the brand-new one. Make certain you have actually certified yourself for the work and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to consider employing one prior to you begin. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your restroom if you have already bought a new tub as well as don't need to alter the plan of your previous water system pipes.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain any type of water remaining in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted access that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in location in between the tap as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind needs to be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using both wood boards under its feet, position the bathtub in the needed setting. The wood boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water system as well as examine all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise inspect the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait up until the tub has actually been utilized at the very least when as this will certainly resolve it into its final position.
Preparing for the Setup
First of all, the sustaining framework provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components as well as installations. They are offered in tubes and also cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Tools You Need to Install a New Bathtub ? Give a remark down the page. We'd be delighted to know your insights about this blog. Hoping to see you back again in the near future. Please take a moment to share this entry if you enjoyed it. We cherish reading our article about How to Install a Bathtub.
Website Report this page